Tile Repair

Guide · Homeowners · 4 min read · Updated 17 November 2026

Why Are My Tiles Hollow or Loose? Causes and Fixes

Short answer

Tiles sound hollow or come loose when the adhesive does not fully bond them to the surface beneath. Common causes are patchy adhesive coverage, an unstable or flexing floor, missing movement joints, water damage behind wall tiles and tiling onto dusty or painted surfaces. Hollow tiles are not always urgent, but loose or cracking ones should be lifted and rebedded. Refixing typically costs £120–£350.

Why Are My Tiles Hollow or Loose? Causes and Fixes

How to check for hollow tiles

Tap each tile gently with a coin, the handle of a screwdriver or a plastic tool. A well bonded tile gives a sharp, solid sound. A hollow tile gives a duller, drummy sound because there is an air gap between the back of the tile and the surface below. Tap the centre and each corner, because a tile can be bonded in the middle and hollow at the edges, or the other way round.

A few hollow tiles in an otherwise solid floor are common and may never cause trouble. The warning signs are tiles that rock underfoot, cracked tiles, grout that is cracking or falling out, and tiles that have lifted so their edges catch. On walls, look for bulging tiles, cracked grout lines and tiles that move when pressed.

The common causes

Most loose tiles trace back to one of a handful of installation or building faults. Identifying the right one matters, because simply regluing tiles without addressing the cause usually means they fail again.

CauseTypical signsFix
Patchy adhesive coverageHollow patches in a grid patternLift and rebed in full adhesive
Flexing timber floorCracks along joists, rocking tilesStiffen floor or overboard, then retile
No movement jointsTiles tenting up in the middle of a floorLift, cut perimeter joints, refix
Water behind wall tilesLoose tiles near shower, crumbling plasterStrip, repair or replace backing, waterproof
Poor surface preparationTiles lift cleanly with little adhesive attachedClean or prime surface, refix
Underfloor heating stressCracks or debonding after heating is usedCheck commissioning, use flexible adhesive

Adhesive coverage and the dot-and-dab problem

On floors, tiles should be bedded on a solid bed of adhesive, combed out with a notched trowel. For larger tiles many tilers also back-butter the tile to fill any hollows. Some floors were laid by placing dabs of adhesive only at the corners and centre of each tile. That leaves voids, and when weight lands over a void the tile flexes and can crack or lose its bond.

BS 5385, the British Standard code of practice for wall and floor tiling, gives guidance on substrates, adhesives, bedding and movement joints, and is a useful benchmark for how floor tiles should be fixed. A repair carried out to that standard involves lifting the affected tiles, removing the old adhesive and rebedding them with full coverage.

Floors that move

Timber floors deflect slightly as people walk across them. Tiles and grout are rigid, so if the floor bends too much they crack or come away. Floorboards are a particularly poor base for tiles. A tiler will usually overboard with cement-based tile backer board or plywood, screwed at close centres, or use a decoupling membrane to absorb small movements.

Concrete floors and screeds can move too, especially if laid recently. A new screed needs to dry before tiling, and if it shrinks after the tiles go down, it can break the bond. Movement joints are also needed around the edges of a tiled floor and at intervals in large areas, so tiles can expand and contract without pushing against walls and tenting upwards.

Loose wall tiles and hidden water

Wall tiles in showers and around baths often come loose because water has got behind them. Failed silicone, cracked grout or a leaking shower valve lets water reach the plaster or plasterboard, which softens and loses its strength. The tiles then pull away with the surface layer still attached.

In this case refixing the tiles alone will not work. The tiler will need to strip the affected area, cut out and replace damaged board or plaster, and ideally fit a tanking system or waterproof backer board before retiling. Find and fix the source of the water first, whether that is resealing, regrouting or a plumber repairing a leak.

  • Check silicone around baths, trays and screens for gaps or black mould
  • Look for cracked or missing grout in the shower area
  • Press tiles near the shower valve and tap to listen for hollowness
  • Look for staining or damp on the ceiling below a first-floor bathroom
  • Stop using the shower until loose tiles have been inspected

What a professional repair involves

Refixing loose or hollow tiles costs £120–£350 for a typical patch. The tiler removes the grout, lifts the tiles carefully with a wide chisel or scraper, cleans old adhesive from the backs and the surface below, and rebeds them with full coverage. Tiles that break during lifting are replaced, so it helps to have spares ready.

Where the problem is the floor or backing, the tiler will explain what needs to happen first and price it separately. That might be overboarding, adding movement joints, or repairing water damaged walls. Be wary of any quote that simply injects adhesive under hollow tiles without investigating, because it rarely addresses the underlying cause.

Older floors and asbestos

If the loose tiles are on a floor in an older property, check what sits underneath before lifting anything. Some vinyl and thermoplastic floor tiles laid before 2000, and the black bitumen adhesives used with them, may contain asbestos. Ceramic tiles are sometimes laid over these older floors. Work that could disturb asbestos is covered by the Control of Asbestos Regulations 2012, so if you suspect it, have a sample tested before any tiles are lifted or broken out. A tiler should stop and advise you if they uncover suspect material during a repair, rather than carrying on and spreading dust.

Questions people also ask

Are hollow sounding tiles a problem?

Not always. A few hollow tiles in a solid floor may never cause trouble. They become a problem when they crack, rock, lift at the edges or the grout around them breaks up. Hollow tiles in showers are more concerning, because they may indicate water behind the tiling.

Can loose tiles be fixed without removing them?

Some products are sold for injecting adhesive under hollow tiles through grout lines, but results are inconsistent and the cause is not addressed. The reliable fix is to lift the tiles, clean off the old adhesive and rebed them with full coverage, after correcting any problem with the surface below.

How much does it cost to refix loose tiles?

Refixing loose or hollow tiles typically costs £120–£350 depending on how many tiles, their size and whether replacements are needed. If the floor needs stiffening or a wall needs new backing board because of water damage, that work is quoted separately once the tiler has inspected it.

Written and checked by the Tile Repair team. Read our editorial policy.

Get a free tile repair quote

Tell us what you need and we'll come back with a clear price.

Request a quote